FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Mikarn Nazuru
Country: Cyprus
Language: English (Spanish)
Genre: Travel
Published (Last): 28 December 2015
Pages: 402
PDF File Size: 15.83 Mb
ePub File Size: 20.66 Mb
ISBN: 148-9-34233-902-3
Downloads: 55579
Price: Free* [*Free Regsitration Required]
Uploader: Gronos

The capacitor backed memory will retain programs for a maximum of 10 days, and requires 30 minutes to recharge upon power up. Always ensure that mounted units and blocks are kept as far as possible from high-voltage cables, high-voltage equipment and power equipment. Ground resistance must be less than ? Do not remove this screw. Circuit protector or fuse? Secure top cover with M3 screw E. The manual has been written to be used by manial and competent personnel.

These engineers should also hrdware trained in the use and maintenance of the completed product. The following instructions are also not suitable. Always make sure the harwdare is turned off, before installing a special function board.

The definition of such a person or persons is as follows; a Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role.

The FX1N does not have battery backup, if a system requires backup of more than 10 days, a peripheral backup power source must be provided. It should be read and understood before attempting to install or use the unit.

Note that the ground cable must not be connected to the same ground as the power circuits. Hqrdware value depends on the switch setting. If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site.

Mitsubishi FX1NMT-DSS Manuals

All maintenance should be carried out in accordance with established safety practices. Software warning 4 Indicates special care must be taken when using this element of software. When the products associated with this manual are used as a system or individually, they must be installed in a suitable enclosure. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

Mahual manual provides information for the installation and use of the FX1N. Upper pot, D read from VR1. If the current leakage is greater than the stated value, then add Rb.

The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA. Never mount them to hhardware floor or ceiling of an enclosure.

Mitsubishi FX1N-24MT-DSS Manuals

This manual contains text, diagrams and explanations which will guide the reader in the correct installation and operation of the FX 1N Series Programmable Controllers. PL E xtension block? E M3 screw to secure top cover. FX0N hardwaree extension units do not have CE certification. Low voltage cables should maual reliably separated or insulated with regard to high voltage cabling. Input circuit power supply? Check D for program scan time, units 0. Take special care not to allow debris to fall inside gardware unit during installation e.

Features table 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top cover Direct mounting holes 4. Units should not be installed in areas subject to the following conditions: Check the power LED is lit.

Occupied points are shown in brackets for input and outputs. Circuit protector or Fuse? The enclosure should be selected and installed in accordance to the local and national standards.